diff --git a/configuration/sensors.md b/configuration/sensors.md
new file mode 100644
index 0000000..19d783f
--- /dev/null
+++ b/configuration/sensors.md
@@ -0,0 +1,73 @@
+---
+layout: page
+title: Sensors
+permalink: /configuration/sensors
+parent: "Configuration"
+nav_order: 4
+---
+
+# Sensors
+
+ESPresense supports various LED and GPIO sensor configurations for enhanced functionality and visual feedback. These settings are accessible from the full Settings view on the device web UI.
+
+![Sensors section of the ESPresense settings UI](/images/sensors_screen.png){: width="360" }
+
+## LEDs
+
+Configure up to 3 addressable LEDs for visual feedback and status indication.
+
+### LED Configuration
+
+For each LED (LED 1, LED 2, LED 3), you can configure:
+
+* **LED Type** - Select the type of addressable LED strip (WS2812, SK6812, etc.)
+* **Pin (-1 to disable)** - GPIO pin number for the LED data line, or -1 to disable
+* **Count (only applies to Addressable LEDs)** - Number of LEDs in the strip
+* **LED Control** - Control mode for the LED behavior
+
+## GPIO Sensors
+
+Configure motion sensors, switches, and buttons connected to GPIO pins.
+
+### PIR (Passive Infrared)
+
+Motion detection using PIR sensors:
+
+* **PIR motion pin type** - Input type configuration for the PIR sensor
+* **PIR motion pin (-1 for disable)** - GPIO pin number for PIR sensor, or -1 to disable
+* **PIR motion timeout (in seconds)** - How long to keep motion state active after detection
+
+### Radar
+
+Motion detection using radar sensors:
+
+* **Radar motion pin type** - Input type configuration for the radar sensor
+* **Radar motion pin (-1 for disable)** - GPIO pin number for radar sensor, or -1 to disable
+* **Radar motion timeout (in seconds)** - How long to keep motion state active after detection
+
+### Switches
+
+Configure up to 2 switch inputs:
+
+#### Switch One / Switch Two
+
+* **Switch pin type** - Input type configuration for the switch
+* **Switch pin (-1 for disable)** - GPIO pin number for the switch, or -1 to disable
+* **Switch timeout (in seconds)** - Debounce timeout for switch activation
+
+### Buttons
+
+Configure up to 2 button inputs:
+
+#### Button One / Button Two
+
+* **Button pin type** - Input type configuration for the button
+* **Button pin (-1 for disable)** - GPIO pin number for the button, or -1 to disable
+* **Button timeout (in seconds)** - Debounce timeout for button presses
+
+## Tips
+
+* Set pin values to -1 to disable any unused sensors or LEDs
+* Ensure GPIO pins don't conflict with other hardware functions
+* Addressable LEDs require proper power supply for multiple LEDs
+* Use appropriate timeout values to avoid false triggers on motion sensors
diff --git a/configuration/settings.md b/configuration/settings.md
index ed903d8..70fe238 100644
--- a/configuration/settings.md
+++ b/configuration/settings.md
@@ -44,10 +44,6 @@ These settings control how ESPresense interprets signal strength. See the full [
 * RSSI adjustment for receiver - Per-node offset to align RSSI across different antennas or hardware.
 * Forget beacon if not seen for (in milliseconds) - How long to keep idle devices before removing them.
 
-## Misc
-
-* Status LED - Blink the LED to the BLE advertisements. A constant slow blink means no mqtt connection.
-* PIR motion pin (0 for disable) - GPIO pin to detect pir motion on
-* Radar motion pin (0 for disable): - GPIO pin to detect radar motion on
+For LED and GPIO sensor configuration (PIR motion, radar motion, switches, buttons), see the [Sensors](sensors) page.
 
 </div>
\ No newline at end of file
diff --git a/images/sensors_screen.png b/images/sensors_screen.png
new file mode 100644
index 0000000..808240a
Binary files /dev/null and b/images/sensors_screen.png differ