Plug-In Battery firmware 1.0103 has been released as beta #5
Replies: 12 comments 25 replies
-
|
Got an E305 and E306 at about 1 p.m. today. Was the update the cause? After waiting 1 hour and then turning it off 10 minutes it worked again. Coincidence? |
Beta Was this translation helpful? Give feedback.
-
|
My battery was offline and lost the connection with the P1 meter for the first time today. |
Beta Was this translation helpful? Give feedback.
-
|
We believe your offline issue has been resolved in 1.0103 |
Beta Was this translation helpful? Give feedback.
-
|
Yes, thanks, was not at home today, but all went automatically without any problems with firmware 1.0103. |
Beta Was this translation helpful? Give feedback.
-
|
Mine gave errors again after it was fully charged and resting. After a quick on/off it came back alive, charging and discharging fine, for now |
Beta Was this translation helpful? Give feedback.
-
|
Klein dingetje. Deze viel me op zojuist. 99% SoC en de PiB geeft aan vol te zijn. (1 PiB in gebruik) |
Beta Was this translation helpful? Give feedback.
-
|
We have released firmware 1.0103 as a replacement for 1.0102. Plug-In Battery This issue has been resolved in |
Beta Was this translation helpful? Give feedback.
-
|
Since the last update something is wrong in the BMS i think. It keeps charging at the 100% and when it reaches 0% it starts topping up with 6 watts, like SOC drift which never happend before pushing the RTE below 75% |
Beta Was this translation helpful? Give feedback.
-
|
In release 1.103 i see that the battery at 100% SoC now for almost 20 minutes is charging with a charging power of 7 Watt and counting. Why this slow or is this an little bug? Normally it's 60 Watt and at 100% charging power goes to 0 Watt. |
Beta Was this translation helpful? Give feedback.
-
|
Correct, mine is staying at 6 watts for 3 hours when at 100% |
Beta Was this translation helpful? Give feedback.
-
|
I dont have this problem. |
Beta Was this translation helpful? Give feedback.
-
|
If the P1 meter registers approximately 50 Watts of power being fed back into the grid, the battery charges at 3 Watts. At the moment when a small amount of power was drawn from the grid, the battery was still charging at 3 Watts. It took 15 minutes until a high-power consumer in the house turned on. The battery responded immediately by starting to discharge. |
Beta Was this translation helpful? Give feedback.
-
|
I have 2 batteries. The 1 one is decharging with round about 600 Watt. |
Beta Was this translation helpful? Give feedback.
-
|
After reinstalling one of four batteries and the P1-dongle I get a message by each of the four batteries that the safety restriction has been reset. It is impossible however to cancel the safety rule after typing (in Dutch) ‘Uitschakelen’. A message appears with an exclamation mark: ‘Not ready (904)
|
Beta Was this translation helpful? Give feedback.
-
|
Zelfde probleem alhier: |
Beta Was this translation helpful? Give feedback.
-
|
@DCSBL Het probleem (het niet kunnen verbinden van de batterijen met de P1-dongle) is opgelost! Na dagen vervangen van ethernetkabels, het compleet vervangen van de wifi-infrastructuur, het hard en soft resetten van de batterijen etc, bleek dat de twee weken geleden vervangen nieuwe P1-dongle de oorzaak is van de verbindingsproblemen. Ik had de oude P1-dongle nog liggen. Die heb ik aangesloten, die kreeg een update en voila, alle accu’s werken. Ik stuur graag de foutieve dongle op, als daar iets uit te leren valt. |
Beta Was this translation helpful? Give feedback.
-
|
Hey @shthpnz, goed om te weten. Wel bijzonder om te horen! We ontvangen je oude P1 Meter graag, wil je hiervoor mailen naar beta@homewizard.com? Als je wilt kunnen we ook kijken of het mogelijk is je data over te zetten op de werkende P1 Meter, dit gaat via de cloud. |
Beta Was this translation helpful? Give feedback.
-
|
@DCSBL: Opgestuurd👍 |
Beta Was this translation helpful? Give feedback.
-
|
@DCSBL : ja graag worden mijn jarenlange data overgezet! |
Beta Was this translation helpful? Give feedback.
-
|
@DCSBL Gisterenavond gaf 1 van de 2 batterijen de melding dat hij niet op een vlakke ondergrond staat. Niets aan veranderd, hij staat waterpas. Even uit en aan hielp niet. |
Beta Was this translation helpful? Give feedback.
-
|
Batterijen laden niet...2800 watt zonnestroom moet voldoende zijn...p1 meter opnieuw aangesloten, geen verandering. 1 pod herstarten gaf chaos. Nu router maar opnieuw gestart. Geen goed gevoel bij. |
Beta Was this translation helpful? Give feedback.
-
|
Update. Na herstaet router geen verandering. De batterijen uitgezet en stroom er af. Opnieuw opgestart. Staan nu te synchroniseren. Batterijen krijgen slechtere connecties overigens. Nog even afwachten maar. Wel gedoe. |
Beta Was this translation helpful? Give feedback.
-
|
@DCSBL Update. Batterijen zijn gesynchroniseerd met netwerk. Laden niet. Hebben wifi verbinding. P1 meter krijgt data slimme meter. Geen idee meer wat kan helpen, zucht. Ik stop er mee, nu al uur aan het kl**ien. |
Beta Was this translation helpful? Give feedback.
-
|
Update. Op Tweakers nog even gezocht. Batterijen langer van de stroom halen heeft gewerkt. Ze laden nu op. Wel random meldingen dat er geen verbinding is maar blijven laden. Misschien dat het geen informatieboodschap in de app moet zijn maar een blokkerende fout, immer, de batterijen laden dan niet. In de faq niet kunnen terugvinden. |
Beta Was this translation helpful? Give feedback.
-
|
Hallo @johnvanderster, weet je zeker dat je vloer waterpas is 😉? Just kidding, we zien dat de data vanuit de tiltsensor soms onjuist is, we zijn bezig met een oplossing hiervoor. We vragen je je geduld hiervoor. |
Beta Was this translation helpful? Give feedback.
-
|
Vanochtend is in app de P1 meter (weer) offline, laatste wifi signaal voldoende. De ring van de meter brandt cintinue groen. Na afkoppelen voeding p1 meter en uit HW verdeelblok en weer aansluiten weer online. Data is vanacht wel binnengekomen.
|
Beta Was this translation helpful? Give feedback.
-
|
Wat doet de batterij? Ik zie dat je de nieuwe beta versie nog niet op de P1 hebt staan. (Zie screenshot van je). Als de batterij wel laad dan zeker die P1 update doen. Zie omschrijving van die release. |
Beta Was this translation helpful? Give feedback.
-
|
Gisterenochtend was het nog te donker en batterijen waren normaal ontladen. Nieuwe firmware was er bij mijn melding nog niet. Nu wel update gehad en draait nog oké. |
Beta Was this translation helpful? Give feedback.
-
|
@johnvanderster, het probleem dat de P1 Meter offline 'lijkt' maar wel data laat zien is verholpen in de P1 Meter 6.0112 |
Beta Was this translation helpful? Give feedback.
-
|
Note We have started a rollout of |
Beta Was this translation helpful? Give feedback.
-
|
What information exactly is being monitored? And what beta features can we expect in the near future? What are you working on? |
Beta Was this translation helpful? Give feedback.
-
|
I've updated the message to be more clear on that. |
Beta Was this translation helpful? Give feedback.
-
|
Plug-In Battery |
Beta Was this translation helpful? Give feedback.
Uh oh!
There was an error while loading. Please reload this page.
Uh oh!
There was an error while loading. Please reload this page.
-
New in Plug-In Battery 1.0102
New in Plug-In Battery 1.0103
Note
As of 31-3-2025 this firmware is available for all Plug-In Batteries.
How to install
The update will be installed automatically. To check if your device has the latest version, follow these instructions: https://helpdesk.homewizard.com/en/articles/9167578-how-do-i-check-if-i-have-the-latest-software-on-my-homewizard-product. Your device must be signed up for the beta channel. Follow these steps to sign up.
Feedback
Leave your feedback as a comment below this announcement during the beta period. We accept both English and Dutch.
Beta Was this translation helpful? Give feedback.
All reactions