Home Assistant Integration

[Crewski]

Hey everyone, I created a custom integration for Home Assistant. It can be installed via HACS or manually by copying into custom_components. The repository can be found at https://github.com/Crewski/njsPC-HA. Once you have it added to HACS and have restarted Home Assistant, you can add it as an integration called njsPC-HA. You just need to put in the IP address of your njsPC instance. The port defaults to 4200. There is no need to enable MQTT as it communicates via RESTapi and socketio. I know there is work for the MQTT discovery happening, but I wanted to learn something new.

I think I have most things working. It is successfully working with my limited equipment (Aquarite SWG, Hayward VS Pump, Colorlogic lights). Please let me know if you have issues with other equipment. I do know that I haven't added Filters into it yet, I don't know how valves operate since I don't have any in my setup.

Two things of note:

1. Selecting a light theme is done as an effect of a light.
   
2. Heaters are controlled by preset mode. The HVAC mode will always be AUTO. This is because heaters can have many different operating modes like "solar preferred" or "heatpump only" that don't match up with home assistant.
   

[rstrouse]

Awesome. Looks like you are using sockets should be pretty responsive.

[seaverd]

@Crewski

This is great! Just installed the integration.

I have all Pentair equipment in a shared body setup (pool with spillover spa) Pentair IC40 Salt Cell, MasterTemp Heater, Intelliflo Pump, Air and Water Temp, Intellibrite lights. When I first installed integration only 12 entities were discovered (none of the climate/heater entities, and none of the lights). I then went to nodejs dashpanel and toggled all my devices through the web dashpanel, rebooted home assistant and I picked up another 5 entities. Sharing this for the benefit of future users of this integration.

I have a couple of discussion points/issues:

1. Since I have a spillover spa, the 95 max degrees was not high enough. I know very little about coding, but see that the climate.py had this value hard coded. I edited my local copy to raise this to our typical max of 100. Ideally it would be nice to have separate max and min temperatures for the spa vs the pool. Not sure if this is possible.
2. With the spillover spa, there is a feature in the NJSPC dashpanel called spillway. Ideally this would just need to be a switch in home assistant. Is there any way to add this?
3. IC40 Salt Cell in NJSPC dashpanel there is a separate salt setpoint for pool mode vs spa mode. For me salt is 100% when in pool mode but only 5 or 10% when I have it running in spa mode. Right now when this gets pulled into homeassistant it is only the salt setpoint for the pool. Wondering if the labeling and ability to have two separate setpoints is possible.

I love how easy and responsive this is...thank you for sharing this integration!

Dan

At first the integration only picked up 12 entities. Not sure w

[Crewski]

@seaverd thanks for the feedback, that's exactly what I need since I don't have those device and bodies. If you don't mind, would you share what your /state/all call looks like. You can either use something like postman or just the browser to make a GET request to http://:4200/state/all. This will give me something to start with. I'll also try to figure out why some entities weren't added at first.

The other helpful thing is to see what the calls are when you are toggling things between pool and spa mode. If you open the developer tools in Chrome/Edge, you should see them when you are making changes in dashPanel. It'll look like this:

[seaverd]

Here is output of states:

{"systemUnits":{"val":0,"name":"english","desc":"English"},"startTime":"2022-07-07T16:50:31.807-0400","time":"2022-08-01T22:40:02.194-0400","valve":0,"delay":{},"batteryVoltage":0,"status":{"val":1,"name":"ready","desc":"Ready","percent":100},"mode":{"val":0,"name":"auto","desc":"Auto"},"appVersion":"7.7.0","appVersionState":{"gitLocalBranch":"master","gitLocalCommit":"2ee8b9b84985a47b324761f57418d826aa441e25","installed":"7.7.0","status":{"val":2,"name":"ahead","desc":"Ahead of published version"},"nextCheckTime":"2022-08-02T14:18:01.488-0400","githubRelease":"7.6.1","equipmentType":"appVersion"},"clockMode":{"val":12,"name":"12 Hour"},"clockSource":{"val":3,"name":"server","desc":"Server"},"controllerType" :"nixie","model":"Nixie Shared is Body","sunrise":"","sunset":"","freeze":false,"valveMode":{"val":3,"name":"spillway","desc":"Spillway"},"temps":{"units":{"val":0,"name":"F","desc":"Fahrenheit"},"bodies":[{"id":1,"heaterOptions":{"total":1,"gas":1,"solar":0,"heatpump":0,"ultratemp":0,"hybrid":0,"mastertemp":0,"maxetherm":0},"isCovered":false,"heaterCooldownDelay":false,"startDelay":false,"stopDelay":false,"showInDashboard":true,"name":"Pool","setPoint":70,"circuit":6,"type":{"val":0,"name":"pool","desc":"Pool"},"heatStatus":{"val":0,"name":"off","desc":"Off"},"isOn":true,"temp":79.71,"heatMode":{"val":1,"name":"off","desc":"Off"}},{"id":2,"heaterOptions":{"total":1,"gas":1,"solar":0,"heatpump":0,"ultratemp":0,"hybrid":0,"mastertemp":0,"maxetherm":0},"isCovered":false,"heaterCooldownDelay":false,"startDelay":false,"stopDelay":false,"showInDashboard":true,"name":"Spa","setPoint":99,"circuit":1,"type":{"val":1,"name":"spa","desc":"Spa"},"heatStatus":{"val":0,"name":"off","desc":"Off"},"isOn":false,"temp":79.83,"heatMode":{"val":2,"name":"heater","desc":"Heater"}}],"waterSensor1":79.71,"air":92.04,"equipmentType":"temps"},"equipment":{"messages":[],"controllerType":"nixie","maxValves":32,"maxCircuits":40,"maxFeatures":32,"maxHeaters":16,"maxLightGroups":16,"maxCircuitGroups":16,"maxSchedules":100,"maxPumps":16,"model":"Nixie Shared Body","maxBodies":2,"shared":true,"dual":false,"single":false,"equipmentType":"equipment","softwareVersion":"1.0.0","bootLoaderVersion":""},"pumps":[{"id":50,"status":{"name":"ok","desc":"Ok","val":1},"pumpOnDelay":false,"name":"Pump","address":96,"type":{"val":3,"name":"vs","desc":"Intelliflo VS","maxPrimingTime":6,"minSpeed":450,"maxSpeed":3450,"maxCircuits":8,"hasAddress":true},"command":10,"mode":0,"driveState":0,"watts":729,"rpm":2400,"flow":0,"ppc":0,"time":243,"isActive":true,"equipmentType":"pump","minSpeed":450,"maxSpeed":3000,"minFlow":0,"maxFlow":130,"circuits":[{"speed":2300,"units":{"val":0,"name":"rpm","desc":"RPM"},"id":1,"circuit":{"id":6,"freezeProtect":false,"action":{"val":0,"name":"ready","desc":"Ready"},"type":{"val":12,"name":"pool","desc":"Pool","hasHeatSource":true,"body":1},"showInFeatures":true,"name":"Pool","startDelay":false,"stopDelay":false,"endTime":"2022-08-02T07:00:00.000-0400","isOn":true,"manualPriorityActive":false,"isActive":true,"startTime":"2022-08-01T21:46:57.117-0400","equipmentType":"circuit"},"master":1},{"speed":2800,"units":{"val":0,"name":"rpm","desc":"RPM"},"id":2,"circuit":{"id":1,"freezeProtect":false,"action":{"val":0,"name":"ready","desc":"Ready"},"type":{"val":13,"name":"spa","desc":"Spa","hasHeatSource":true,"body":2},"showInFeatures":true,"name":"Spa","isActive":true,"endTime":"2022-08-01T23:46:00.528-0400","isOn":false,"manualPriorityActive":false,"startDelay":false,"stopDelay":false,"equipmentType":"circuit"},"master":1},{"speed":2400,"units":{"val":0,"name":"rpm","desc":"RPM"},"id":3,"circuit":{"id":129,"freezeProtect":false,"isOn":true,"name":"Spillway","type":{"val":1,"name":"spillway","desc":"Spillway"},"showInFeatures":true,"manualPriorityActive":false,"endTime":"2022-08-01T22:49:20.068-0400","equipmentType":"feature"},"master":1}]}],"valves":[{"id":1,"name":"Intake","type":{"val":0,"name":"standard","desc":"Standard"},"isDiverted":false,"equipmentType":"valve","circuit":{"id":247,"isActive":true,"isOn":true,"type":{"val":247,"name":"poolSpa","desc":"Pool/Spa"},"name":"Pool/Spa","equipmentType":"virtualCircuit"},"isIntake":true,"isReturn":false,"isActive":true,"pinId":0},{"id":2,"name":"Return","type":{"val":0,"name":"standard","desc":"Standard"},"isDiverted":true,"equipmentType":"valve","circuit":{"id":247,"isActive":true,"isOn":true,"type":{"val":247,"name":"poolSpa","desc":"Pool/Spa"},"name":"Pool/Spa","equipmentType":"virtualCircuit"},"isIntake":false,"isReturn":true,"isActive":true,"pinId":0}],"heaters":[{"id":256,"startupDelay":false,"shutdownDelay":false,"name":"Heater","type":{"val":1,"name":"gas","desc":"Gas Heater","hasAddress":false},"endTime":"2022-08-01T21:45:57.546-0400","isOn":false,"bodyId":0,"startTime":"2022-08-01T21:45:56.606-0400","equipmentType":"heater"}],"chlorinators":[{"id":1,"disabled":false,"poolSetpoint":100,"spaSetpoint":10,"superChlorHours":8,"type":{"val":0,"name":"pentair","desc":"Pentair"},"model":{"val":3,"name":"intellichlor--40","desc":"IntelliChlor IC40","capacity":40000,"chlorinePerDay":1.4,"chlorinePerSec":0.000016203703703703704},"body":{"val":32,"name":"poolspa","desc":"Pool/Spa"},"name":"IC40 Salt Cl2","isActive":true,"lastComm":1659408056788,"superChlor":false,"targetOutput":100,"saltLevel":3150,"saltRequired":70.83,"status":{"val":0,"name":"ok","desc":"Ok"},"currentOutput":100,"superChlorRemaining":0,"equipmentType":"chlorinator","saltTarget":3400}],"circuits":[{"id":6,"freezeProtect":false,"action":{"val":0,"name":"ready","desc":"Ready"},"type":{"val":12,"name":"pool","desc":"Pool","hasHeatSource":true,"body":1},"showInFeatures":true,"name":"Pool","startDelay":false,"stopDelay":false,"endTime":"2022-08-02T07:00:00.000-0400","isOn":true,"manualPriorityActive":false,"isActive":true,"startTime":"2022-08-01T21:46:57.117-0400","equipmentType":"circuit"},{"id":2,"freezeProtect":false,"action":{"val":0,"name":"ready","desc":"Ready"},"type":{"val":5,"name":"intellibrite","desc":"Intellibrite","isLight":true,"theme":"intellibrite"},"isActive":true,"name":"Pool Lights","showInFeatures":true,"startDelay":false,"stopDelay":false,"endTime":"2022-08-01T22:59:36.824-0400","isOn":false,"manualPriorityActive":false,"lightingTheme":{"val":2,"name":"blue","desc":"Blue","types":["intellibrite","magicstream"],"sequence":8},"equipmentType":"circuit"},{"id":3,"freezeProtect":false,"action":{"val":0,"name":"ready","desc":"Ready"},"type":{"val":5,"name":"intellibrite","desc":"Intellibrite","isLight":true,"theme":"intellibrite"},"isActive":true,"name":"Spa Lights","showInFeatures":true,"startDelay":false,"stopDelay":false,"endTime":"2022-08-01T23:45:49.988-0400","isOn":false,"manualPriorityActive":false,"lightingTheme":{"val":2,"name":"blue","desc":"Blue","types":["intellibrite","magicstream"],"sequence":8},"equipmentType":"circuit"},{"id":4,"freezeProtect":false,"action":{"val":0,"name":"ready","desc":"Ready"},"type":{"val":4,"name":"light","desc":"Light","isLight":true},"isActive":true,"name":"Diving Lights","showInFeatures":true,"startDelay":false,"stopDelay":false,"endTime":"2022-08-01T21:59:14.718-0400","isOn":false,"manualPriorityActive":false,"equipmentType":"circuit"},{"id":5,"freezeProtect":false,"action":{"val":0,"name":"ready","desc":"Ready"},"type":{"val":0,"name":"generic","desc":"Generic"},"isActive":true,"name":"Slide","showInFeatures":true,"startDelay":false,"stopDelay":false,"endTime":"2022-08-01T23:45:40.394-0400","isOn":false,"manualPriorityActive":false,"equipmentType":"circuit"},{"id":1,"freezeProtect":false,"action":{"val":0,"name":"ready","desc":"Ready"},"type":{"val":13,"name":"spa","desc":"Spa","hasHeatSource":true,"body":2},"showInFeatures":true,"name":"Spa","isActive":true,"endTime":"2022-08-01T23:46:00.528-0400","isOn":false,"manualPriorityActive":false,"startDelay":false,"stopDelay":false,"equipmentType":"circuit"}],"features":[{"id":129,"freezeProtect":false,"isOn":true,"name":"Spillway","type":{"val":1,"name":"spillway","desc":"Spillway"},"showInFeatures":true,"manualPriorityActive":false,"endTime":"2022-08-01T22:49:20.068-0400","equipmentType":"feature"}],"circuitGroups":[],"lightGroups":[],"virtualCircuits":[{"id":246,"isActive":true,"isOn":false,"type":{"val":246,"name":"freeze","desc":"Freeze"},"name":"Freeze","equipmentType":"virtualCircuit"},{"id":247,"isActive":true,"isOn":true,"type":{"val":247,"name":"poolSpa","desc":"Pool/Spa"},"name":"Pool/Spa","equipmentType":"virtualCircuit"},{"id":258,"isActive":true,"isOn":false,"type":{"val":258,"name":"anyHeater","desc":"Any Heater"},"name":"Any Heater","equipmentType":"virtualCircuit"},{"id":245,"isActive":true,"isOn":false,"type":{"val":245,"name":"spaHeater","desc":"Spa Heater"},"name":"Spa Heater","equipmentType":"virtualCircuit"},{"id":244,"isActive":true,"isOn":false,"type":{"val":244,"name":"poolHeater","desc":"Pool Heater"},"name":"Pool Heater","equipmentType":"virtualCircuit"}],"covers":[],"filters":[{"id":1,"name":"Filter","body":{"val":32,"name":"poolspa","desc":"Pool/Spa"},"filterType":{"val":1,"name":"cartridge","desc":"Cartridge","hasBackwash":false},"isOn":true,"pressureUnits":{"val":0,"name":"psi","desc":"Pounds per Sqare Inch"},"equipmentType":"filter"}],"schedules":[{"id":2,"startTimeType":{"val":0,"name":"manual","desc":"Manual"},"endTimeType":{"val":0,"name":"manual","desc":"Manual"},"display":{"val":0,"name":"always","desc":"Always"},"circuit":{"id":6,"freezeProtect":false,"action":{"val":0,"name":"ready","desc":"Ready"},"type":{"val":12,"name":"pool","desc":"Pool","hasHeatSource":true,"body":1},"showInFeatures":true,"name":"Pool","startDelay":false,"stopDelay":false,"endTime":"2022-08-02T07:00:00.000-0400","isOn":true,"manualPriorityActive":false,"isActive":true,"startTime":"2022-08-01T21:46:57.117-0400","equipmentType":"circuit"},"scheduleDays":{"val":127,"days":[{"name":"sun","desc":"Sunday","dow":0,"bitval":64},{"name":"sat","desc":"Saturday","dow":6,"bitval":32},{"name":"fri","desc":"Friday","dow":5,"bitval":16},{"name":"thu","desc":"Thursday","dow":4,"bitval":8},{"name":"wed","desc":"Wednesday","dow":3,"bitval":4},{"name":"tue","desc":"Tuesday","dow":2,"bitval":2},{"name":"mon","desc":"Monday","dow":1,"bitval":1}]},"scheduleType":{"val":128,"name":"repeat","desc":"Repeats","startDate":false,"startTime":true,"endTime":true,"days":"multi","heatSource":true,"heatSetpoint":true},"heatSetpoint":78,"coolSetpoint":100,"heatSource":{"val":0,"name":"nochange","desc":"No Change"},"startTime":60,"endTime":420,"startDate":"2022-06-02T00:00:00.000-0400","isActive":true,"disabled":false,"isOn":false,"manualPriorityActive":false,"equipmentType":"schedule"},{"id":3,"startTimeType":{"val":0,"name":"manual","desc":"Manual"},"endTimeType":{"val":0,"name":"manual","desc":"Manual"},"display":{"val":0,"name":"always","desc":"Always"},"circuit":{"id":129,"freezeProtect":false,"isOn":true,"name":"Spillway","type":{"val":1,"name":"spillway","desc":"Spillway"},"showInFeatures":true,"manualPriorityActive":false,"endTime":"2022-08-01T22:49:20.068-0400","equipmentType":"feature"},"scheduleDays":{"val":127,"days":[{"name":"sun","desc":"Sunday","dow":0,"bitval":64},{"name":"sat","desc":"Saturday","dow":6,"bitval":32},{"name":"fri","desc":"Friday","dow":5,"bitval":16},{"name":"thu","desc":"Thursday","dow":4,"bitval":8},{"name":"wed","desc":"Wednesday","dow":3,"bitval":4},{"name":"tue","desc":"Tuesday","dow":2,"bitval":2},{"name":"mon","desc":"Monday","dow":1,"bitval":1}]},"scheduleType":{"val":128,"name":"repeat","desc":"Repeats","startDate":false,"startTime":true,"endTime":true,"days":"multi","heatSource":true,"heatSetpoint":true},"heatSetpoint":78,"coolSetpoint":100,"heatSource":{"val":0,"name":"nochange","desc":"No Change"},"startTime":420,"endTime":480,"startDate":"2022-06-02T00:00:00.000-0400","isActive":true,"disabled":false,"isOn":false,"manualPriorityActive":false,"equipmentType":"schedule"},{"id":4,"startTimeType":{"val":0,"name":"manual","desc":"Manual"},"endTimeType":{"val":0,"name":"manual","desc":"Manual"},"display":{"val":0,"name":"always","desc":"Always"},"circuit":{"id":6,"freezeProtect":false,"action":{"val":0,"name":"ready","desc":"Ready"},"type":{"val":12,"name":"pool","desc":"Pool","hasHeatSource":true,"body":1},"showInFeatures":true,"name":"Pool","startDelay":false,"stopDelay":false,"endTime":"2022-08-02T07:00:00.000-0400","isOn":true,"manualPriorityActive":false,"isActive":true,"startTime":"2022-08-01T21:46:57.117-0400","equipmentType":"circuit"},"scheduleDays":{"val":127,"days":[{"name":"sun","desc":"Sunday","dow":0,"bitval":64},{"name":"sat","desc":"Saturday","dow":6,"bitval":32},{"name":"fri","desc":"Friday","dow":5,"bitval":16},{"name":"thu","desc":"Thursday","dow":4,"bitval":8},{"name":"wed","desc":"Wednesday","dow":3,"bitval":4},{"name":"tue","desc":"Tuesday","dow":2,"bitval":2},{"name":"mon","desc":"Monday","dow":1,"bitval":1}]},"scheduleType":{"val":128,"name":"repeat","desc":"Repeats","startDate":false,"startTime":true,"endTime":true,"days":"multi","heatSource":true,"heatSetpoint":true},"heatSetpoint":78,"coolSetpoint":100,"heatSource":{"val":0,"name":"nochange","desc":"No Change"},"startTime":600,"endTime":720,"startDate":"2022-06-02T00:00:00.000-0400","isActive":true,"disabled":false,"isOn":false,"manualPriorityActive":false,"equipmentType":"schedule"},{"id":1,"startTimeType":{"val":0,"name":"manual","desc":"Manual"},"endTimeType":{"val":0,"name":"manual","desc":"Manual"},"display":{"val":0,"name":"always","desc":"Always"},"circuit":{"id":129,"freezeProtect":false,"isOn":true,"name":"Spillway","type":{"val":1,"name":"spillway","desc":"Spillway"},"showInFeatures":true,"manualPriorityActive":false,"endTime":"2022-08-01T22:49:20.068-0400","equipmentType":"feature"},"scheduleDays":{"val":127,"days":[{"name":"sun","desc":"Sunday","dow":0,"bitval":64},{"name":"sat","desc":"Saturday","dow":6,"bitval":32},{"name":"fri","desc":"Friday","dow":5,"bitval":16},{"name":"thu","desc":"Thursday","dow":4,"bitval":8},{"name":"wed","desc":"Wednesday","dow":3,"bitval":4},{"name":"tue","desc":"Tuesday","dow":2,"bitval":2},{"name":"mon","desc":"Monday","dow":1,"bitval":1}]},"scheduleType":{"val":128,"name":"repeat","desc":"Repeats","startDate":false,"startTime":true,"endTime":true,"days":"multi","heatSource":true,"heatSetpoint":true},"heatSetpoint":78,"coolSetpoint":100,"heatSource":{"val":0,"name":"nochange","desc":"No Change"},"startTime":720,"endTime":780,"startDate":"2022-06-02T00:00:00.000-0400","isActive":true,"disabled":false,"isOn":false,"manualPriorityActive":false,"equipmentType":"schedule"},{"id":5,"startTimeType":{"val":0,"name":"manual","desc":"Manual"},"endTimeType":{"val":0,"name":"manual","desc":"Manual"},"display":{"val":0,"name":"always","desc":"Always"},"circuit":{"id":6,"freezeProtect":false,"action":{"val":0,"name":"ready","desc":"Ready"},"type":{"val":12,"name":"pool","desc":"Pool","hasHeatSource":true,"body":1},"showInFeatures":true,"name":"Pool","startDelay":false,"stopDelay":false,"endTime":"2022-08-02T07:00:00.000-0400","isOn":true,"manualPriorityActive":false,"isActive":true,"startTime":"2022-08-01T21:46:57.117-0400","equipmentType":"circuit"},"scheduleDays":{"val":127,"days":[{"name":"sun","desc":"Sunday","dow":0,"bitval":64},{"name":"sat","desc":"Saturday","dow":6,"bitval":32},{"name":"fri","desc":"Friday","dow":5,"bitval":16},{"name":"thu","desc":"Thursday","dow":4,"bitval":8},{"name":"wed","desc":"Wednesday","dow":3,"bitval":4},{"name":"tue","desc":"Tuesday","dow":2,"bitval":2},{"name":"mon","desc":"Monday","dow":1,"bitval":1}]},"scheduleType":{"val":128,"name":"repeat","desc":"Repeats","startDate":false,"startTime":true,"endTime":true,"days":"multi","heatSource":true,"heatSetpoint":true},"heatSetpoint":78,"coolSetpoint":100,"heatSource":{"val":0,"name":"nochange","desc":"No Change"},"startTime":900,"endTime":1200,"startDate":"2022-06-02T00:00:00.000-0400","isActive":true,"disabled":false,"manualPriorityActive":false,"isOn":false,"equipmentType":"schedule"}],"chemControllers":[],"delays":[]}

[seaverd]

@Crewski As a start, see above for states all output. I’ll have to do the toggle with developer console sometime tomorrow. Thanks,
Dan

[Crewski]

@seaverd I went ahead and made some changes to hopefully cover your issues. There is a beta release out (v0.3.1-beta4). In HACS if you don't have beta releases selected, go to the njsPC-HA integration and click the 3 dots in the top right. Then click Redownload. A popup will appear where you can select beta releases. Download v0.3.1-beta4 and restart home assistant. Let me know if this takes care of things, especially the spillway since I couldn't recreate that in my fake setup I tried to make.

*the image shows the wrong beta version

[seaverd]

Thanks for the changes! Only thing I noticed is pool happened to be in spillway mode when I installed the beta integration and rebooted. When HA came back up it did not show pool as being in spillway mode. I toggled spillway mode so that turned it off and then toggled it on and it came on. Has stayed in sync sense. Not sure if that is expected or how it gets its initial value/status on a reboot.

…

On Tue, Aug 2, 2022 at 9:15 AM Crewski ***@***.***> wrote: @seaverd <https://github.com/seaverd> I went ahead and made some changes to hopefully cover your issues. There is a beta release out (v0.3.1-beta2). In HACS if you don't have beta releases selected, go to the njsPC-HA integration and click the 3 dots in the top right. Then click Redownload. A popup will appear where you can select beta releases. Download v0.3.1-beta2 and restart home assistant. Let me know if this takes care of things, especially the spillway since I couldn't recreate that in my fake setup I tried to make. [image: image] <https://user-images.githubusercontent.com/8012153/182383511-67edca58-c05b-4013-8413-28d195bf23f0.png> — Reply to this email directly, view it on GitHub <#559 (reply in thread)>, or unsubscribe <https://github.com/notifications/unsubscribe-auth/AAU53BJEVN5GIL2BX3PCDVDVXENQXANCNFSM55CMANFQ> . You are receiving this because you were mentioned.Message ID: <tagyoureit/nodejs-poolController/repo-discussions/559/comments/3307977@ github.com>

[Crewski]

But everything else worked with the SWG Spa/Pool setpoint and heater min/max values?

I'm not sure why it didn't sync up initially. It's looking for the "isOn" attribute obtained from the /state/all call. If it can't find it, it defaults to off. You didn't happen to reboot njsPC prior and not change the spillway yet, did you? I noticed that issue with I was messing with lights of it not having the "isOn" attribute until it changed, which is why I added the try/except block to default to off.

In this case, self._circuit is really the feature.

    @property
    def is_on(self):
        try:
            return self._circuit["isOn"]
        except:
            return False

[seaverd]

SWG spa/pool setpoint and heater max min temps work great. I did update njsPC prior…so your explanation is entirely possible. So everything is looking good. Thanks for your prompt assistance! Dan

…

On Tue, Aug 2, 2022 at 2:23 PM Crewski ***@***.***> wrote: But everything else worked with the SWG Spa/Pool setpoint and heater min/max values? I'm not sure why it didn't sync up initially. It's looking for the "isOn" attribute obtained from the /state/all call. If it can't find it, it defaults to off. You didn't happen to reboot njsPC prior and not change the spillway yet, did you? I noticed that issue with I was messing with lights of it not having the "isOn" attribute until it changed, which is why I added the try/except block to default to off. [image: image] <https://user-images.githubusercontent.com/8012153/182446115-9a129b84-1025-496b-9a2d-46f23ab0c506.png> In this case, self._circuit is really the feature. @Property def is_on(self): try: return self._circuit["isOn"] except: return False — Reply to this email directly, view it on GitHub <#559 (reply in thread)>, or unsubscribe <https://github.com/notifications/unsubscribe-auth/AAU53BJRLDNSLRDBJSQYIXTVXFRSDANCNFSM55CMANFQ> . You are receiving this because you were mentioned.Message ID: <tagyoureit/nodejs-poolController/repo-discussions/559/comments/3310381@ github.com>

[Crewski]

v0.3.2 has been released. The two changes are:

1. If there is only one heater installed, the climate entity will use the HVAC modes of OFF and HEAT. If there are more than 1 and you end up with options like "solar prefered", then the HVAC will always be AUTO and you will need to use the presets to select the mode. This is determined by a call to /config/body/{id}/heatModes.
2. Entities will go unavailable when connection is lost to njsPC. It'll try to reconnect every 10 seconds. Entities become available again upon reconnection.

[lockeandev]

I have a pentair vsf pump. The integration gives me an rpm entity but not a gpm or flow entity. Would it be possible to add that?

[Crewski]

@lockeandev I added a flow sensor if available. I have a Hayward VS that doesn't report flow, and I wasn't able to emulate one so hopefully it works. It should check to see if a "flow" value is available and if so add it. This is version 0.3.5.

Let me know if it works or not, or if there is anything else that needs to be added. Thanks for testing it out.

[lockeandev]

Works great. Thank you.

How are lights supposed to work? I have light entities for my light circuits but I don't see anywhere to adjust the theme? Your screen shot above shows the effect drop-down but I don't see that on any of my light entities. I have pentair microbrites and pentair magic stream LEDs.

[Crewski]

@lockeandev the light show options are only visible in Home Assistant when the light is on. If they don't show when they are on we can work on figuring that out.

[psmith3]

Hey @Crewski, this is awesome! I did all my integration in HA using MQTT and was at the point that I needed to switch my formatting over to the latest MQTT Sensor formatting. I found your integration and this looks like a better approach. Took some researching on how to display the Salt Level and Salt Required Attributes, so I figured I would share it here.

type: vertical-stack
cards:

• type: gauge
  entity: sensor.aquarite_salt_level
  min: 2000
  max: 4000
  severity:
  green: 2700
  yellow: 3400
  red: 1
  needle: true
• type: conditional
  conditions:
  • entity: sensor.aquarite_salt_level
    state_not: '3300'
  • entity: sensor.aquarite_salt_level
    state_not: '3400'
  • entity: sensor.aquarite_salt_level
    state_not: '3500'
  • entity: sensor.aquarite_salt_level
    state_not: '3600'
    card:
    type: markdown
    content: >-
    Add {{ ( states('sensor.salt_required') |
    int /40 ) | round(0) }}, 40 lb bags of Salt ({{
    (states('sensor.salt_required')) }} lbs.) to reach {{
    (states('sensor.pool_salt_target_level')) }} ppm
• type: gauge
  entity: sensor.aquarite_current_output
  min: 0
  max: 100
  needle: true
  segments:
  • from: 0
    color: '#db4437'
  • from: 5
    color: '#009dff'
  • from: 95
    color: '#ffa600'
• type: entities
  entities:
  • entity: sensor.aquarite_status
  • entity: switch.pool
  • entity: number.aquarite_pool_setpoint
  • entity: number.aquarite_superchlor_hours
  • entity: switch.aquarite_super_chlorinate
  • entity: sensor.aquarite_salt_level
    secondary_info: none
  • type: attribute
    entity: sensor.aquarite_salt_level
    attribute: salt_target
    name: Salt Target Level
    icon: mdi:target
    suffix: PPM
  • type: attribute
    entity: sensor.aquarite_salt_level
    attribute: salt_required
    name: Salt Required
    suffix: lbs
    show_header_toggle: false
    state_color: true
    title: AquaRite 940 Salt Chlorinator

[Crewski]

@psmith3 glad you found it helpful. I have the salt needed and salt target as attributes for the salt level sensor. You can pull them out with a template sensor if you want. If there is more need than that, I can make them individual sensors as well.

[psmith3]

Although I did figure out how to pull the attributes out, it would be nice and more intuitive if they were exposed as their own sensors. Thanks again On Sep 7, 2022, at 6:44 PM, Crewski ***@***.***> wrote:  @psmith3<https://nam12.safelinks.protection.outlook.com/?url=https%3A%2F%2Fgithub.com%2Fpsmith3&data=05%7C01%7C%7C89c3d3b1cf834fe378bf08da912ae53b%7C84df9e7fe9f640afb435aaaaaaaaaaaa%7C1%7C0%7C637981910668156830%7CUnknown%7CTWFpbGZsb3d8eyJWIjoiMC4wLjAwMDAiLCJQIjoiV2luMzIiLCJBTiI6Ik1haWwiLCJXVCI6Mn0%3D%7C3000%7C%7C%7C&sdata=a6CjU8vMS9wmzcItnizZ6N1b%2FdOWFIh85zpuacocoew%3D&reserved=0> glad you found it helpful. I have the salt needed and salt target as attributes for the salt level sensor. You can pull them out with a template sensor if you want. If there is more need than that, I can make them individual sensors as well. — Reply to this email directly, view it on GitHub<https://nam12.safelinks.protection.outlook.com/?url=https%3A%2F%2Fgithub.com%2Ftagyoureit%2Fnodejs-poolController%2Fdiscussions%2F559%23discussioncomment-3589644&data=05%7C01%7C%7C89c3d3b1cf834fe378bf08da912ae53b%7C84df9e7fe9f640afb435aaaaaaaaaaaa%7C1%7C0%7C637981910668156830%7CUnknown%7CTWFpbGZsb3d8eyJWIjoiMC4wLjAwMDAiLCJQIjoiV2luMzIiLCJBTiI6Ik1haWwiLCJXVCI6Mn0%3D%7C3000%7C%7C%7C&sdata=5D1j%2FYioenZXlSVf%2BpoMLpMwZYPJc5HBkKoX7AaxU6M%3D&reserved=0>, or unsubscribe<https://nam12.safelinks.protection.outlook.com/?url=https%3A%2F%2Fgithub.com%2Fnotifications%2Funsubscribe-auth%2FADNVCK6NBU5CHUY5RO57W3LV5ESFPANCNFSM55CMANFQ&data=05%7C01%7C%7C89c3d3b1cf834fe378bf08da912ae53b%7C84df9e7fe9f640afb435aaaaaaaaaaaa%7C1%7C0%7C637981910668156830%7CUnknown%7CTWFpbGZsb3d8eyJWIjoiMC4wLjAwMDAiLCJQIjoiV2luMzIiLCJBTiI6Ik1haWwiLCJXVCI6Mn0%3D%7C3000%7C%7C%7C&sdata=LGAcWXiz2ADh8eVI1kaIMjVCyLHYN6D7rRd2DjQ6i%2FU%3D&reserved=0>. You are receiving this because you were mentioned.Message ID: ***@***.***>

[Crewski]

@psmith3 I added them as their own sensor in v0.3.6. Should be available now.

[psmith3]

Awesome! Thank you. On Sep 8, 2022, at 6:31 AM, Crewski ***@***.***> wrote:  @psmith3<https://nam12.safelinks.protection.outlook.com/?url=https%3A%2F%2Fgithub.com%2Fpsmith3&data=05%7C01%7C%7Caff43bb721d940350e7d08da918da1bc%7C84df9e7fe9f640afb435aaaaaaaaaaaa%7C1%7C0%7C637982334737345218%7CUnknown%7CTWFpbGZsb3d8eyJWIjoiMC4wLjAwMDAiLCJQIjoiV2luMzIiLCJBTiI6Ik1haWwiLCJXVCI6Mn0%3D%7C3000%7C%7C%7C&sdata=Wx%2Bvii2VjKK%2BcmGZhl6MIMLK0GqqxohYAgvxfkhqSxo%3D&reserved=0> I added them as their own sensor in v0.3.6. Should be available now. — Reply to this email directly, view it on GitHub<https://nam12.safelinks.protection.outlook.com/?url=https%3A%2F%2Fgithub.com%2Ftagyoureit%2Fnodejs-poolController%2Fdiscussions%2F559%23discussioncomment-3593733&data=05%7C01%7C%7Caff43bb721d940350e7d08da918da1bc%7C84df9e7fe9f640afb435aaaaaaaaaaaa%7C1%7C0%7C637982334737345218%7CUnknown%7CTWFpbGZsb3d8eyJWIjoiMC4wLjAwMDAiLCJQIjoiV2luMzIiLCJBTiI6Ik1haWwiLCJXVCI6Mn0%3D%7C3000%7C%7C%7C&sdata=x%2B6jAoBK6bBS2YRrdzgUXLuzEahE7frsAnvW0kByg%2Bs%3D&reserved=0>, or unsubscribe<https://nam12.safelinks.protection.outlook.com/?url=https%3A%2F%2Fgithub.com%2Fnotifications%2Funsubscribe-auth%2FADNVCK2RYR4W2WOMUD5CFFLV5HE75ANCNFSM55CMANFQ&data=05%7C01%7C%7Caff43bb721d940350e7d08da918da1bc%7C84df9e7fe9f640afb435aaaaaaaaaaaa%7C1%7C0%7C637982334737345218%7CUnknown%7CTWFpbGZsb3d8eyJWIjoiMC4wLjAwMDAiLCJQIjoiV2luMzIiLCJBTiI6Ik1haWwiLCJXVCI6Mn0%3D%7C3000%7C%7C%7C&sdata=8L6L3Oo2qzCNT3XdTGb%2BYt7fpVgqEkW0%2FcKIGCGGHJw%3D&reserved=0>. You are receiving this because you were mentioned.Message ID: ***@***.***>

[seaverd]

I have updated, so far everything is working great. I do have a feature request. Can you add a sensor that tracks the actual IC40 salt cell output? I believe its the targetOutput value from my /state/all My reason is it would be nice to actually have a graph that shows the output percentage. Thanks! Dan

…

On Fri, Aug 5, 2022 at 9:30 AM Crewski ***@***.***> wrote: v0.3.2 has been released. The two changes are: 1. If there is only one heater installed, the climate entity will use the HVAC modes of OFF and HEAT. If there are more than 1 and you end up with options like "solar prefered", then the HVAC will always be AUTO and you will need to use the presets to select the mode. This is determined by a call to /config/body/{id}/heatModes. 2. Entities will go unavailable when connection is lost to njsPC. It'll try to reconnect every 10 seconds. Entities become available again upon reconnection. — Reply to this email directly, view it on GitHub <#559 (comment)>, or unsubscribe <https://github.com/notifications/unsubscribe-auth/AAU53BLJNFU4MUMBUR35YJLVXUJOXANCNFSM55CMANFQ> . You are receiving this because you were mentioned.Message ID: <tagyoureit/nodejs-poolController/repo-discussions/559/comments/3333677@ github.com>

[tagyoureit]

There will be a currentOutput field for the chlorinator. This will be the actual percentage output. The targetOutput is what you want it to be. Of the circuit (pool or spa) is off or the chlor has comms issues there will be a difference in target vs current output.

For a bit of background, the salt cell only ever outputs 0% or 100% if you were to measure it with a volt meter. When you set it to 50% it will be on for 2.5 mins and then off for 2.5 mins. It is a common misconception that the salt cell changes the strength of the chemical reaction but it is really a % of time calculation.

[Crewski]

@seaverd I thought I had replied but I guess it didn't take. Anyway, targetOutput should have been available as an attribute of the current output entity. I went ahead a broke it out to its own sensor for ease of use. Go ahead an update njsPC-HA and you should be good to go.

[DrJeff]

Are the heaters inside of HA set with a limit at 95° or is it just me. They show fine if changed in njsPC but not HA it's maxed at 95°

[Crewski]

I have it setup where a pool has temp limits of 70-95 and a spa is 90-104. Do you have your pool higher than 95? Or did it not properly capture that you have a spa?

This was just to put some sensible limits in place, but if it isn't working right we can hard code values that would cover both pool and spa, so 70-104 for every climate.

[DrJeff]

Ok maybe because I have a dual body setup it thinks 2 pools not a spa

[rstrouse]

The max for all bodies in Pentair land is 40C or 104F depending on units and the min is 5C or 40F. Not really a sensible number unless I suppose you are trying to keep it from freezing.

[seaverd]

Crewski, Everything has been working flawlessly for months. Thanks for all of your work on this. One question, would it be possible to add pump speeds to Home Assistant? I have a Pentair SVRS pump and I am able to change the RPMs in the nodejs-pool controller dashboard, but I am unable to do so via homeassistant. Thanks for considering this feature/enhancement. Dan

…

On Sat, Oct 22, 2022 at 3:23 PM rstrouse ***@***.***> wrote: The max for all bodies in Pentair land is 40C or 104F depending on units. — Reply to this email directly, view it on GitHub <#559 (reply in thread)>, or unsubscribe <https://github.com/notifications/unsubscribe-auth/AAU53BJQUQQ725POTRBQGHLWEQ5MBANCNFSM55CMANFQ> . You are receiving this because you were mentioned.Message ID: <tagyoureit/nodejs-poolController/repo-discussions/559/comments/3941217@ github.com>

[Crewski]

@seaverd, glad its been working well so far. Are you changing the pump speeds for the circuits like in the picture below? If so, I'd have to think about that one. I would argue that is part of the configuration done through njspc and not something to be controlled via Home Assistant. My understanding is that if you need different speeds, you create a circuit and assign it a speed. Then just toggle that circuit on/off when that speed is needed.

[seaverd]

@Crewski. Your suggestion makes perfect sense. Basically I needed a circuit to change the speed of the pump for vacuuming/cleaning. I am all set...thanks! I was just clicking the plus and minus next the RPM values in njspc and figured there would be a way to make a slider to do the same thing in HA. Thanks again! Dan

…

On Thu, Nov 3, 2022 at 7:15 AM Crewski ***@***.***> wrote: @seaverd <https://github.com/seaverd>, glad its been working well so far. Are you changing the pump speeds for the circuits like in the picture below? If so, I'd have to think about that one. I would argue that is part of the configuration done through njspc and not something to be controlled via Home Assistant. My understanding is that if you need different speeds, you create a circuit and assign it a speed. Then just toggle that circuit on/off when that speed is needed. [image: image] <https://user-images.githubusercontent.com/8012153/199707071-ba28471d-ad1e-42ea-a4cb-04aebcca331b.png> — Reply to this email directly, view it on GitHub <#559 (reply in thread)>, or unsubscribe <https://github.com/notifications/unsubscribe-auth/AAU53BMN2OKV37JMBIK5QWTWGONEZANCNFSM55CMANFQ> . You are receiving this because you were mentioned.Message ID: <tagyoureit/nodejs-poolController/repo-discussions/559/comments/4046085@ github.com>

[FlaMike]

I am cross-posting this from the poolController discussion so please forgive me if you see it in both places.

I have an Easytouch 2 4 controller and I am running version 7.7.0 of the poolController. I am also running Home Assistant and using the njsPC-HA integration to bring and control the pool from Home Assistant. Everything has been working flawlessly for months.

A couple of days ago, for the first time, I tried to turn on the pool heater from Home Assistant. I am using the climate.pool_heater entity in njsPC-HA. I can change the heater temperature setpoint from HA without any problem and the change is reflected correctly on the Easytouch controller.

However, when I try to turn the heater on from HA, it immediately changes back to off. In the poolControllerDashboard web interface, the heater is displayed as a virtual circuit but I cannot turn it on or off. The heater does appear under heaters in the Dashboard and as a virtual circuit.

Can you kindly let me know what I need to do in order to use the heater via the dashboard and hopefully HA? I can control it from the Easytouch controller, but I'd really like to be able to use the poolController instead of the Easytouch.

Thanks for your help!

[FlaMike]

For what it's worth, I am using the scheduler HACS addon and the scheduler card to set schedules for the pool equipment from HA. It works fine with njcPC and njcPC-HA.

[mjpsr11]

Not finding a 'scheduler' in the HACS addons. Can you give more details?

[FlaMike]

My bad, it's called the "scheduler-component." Both the component and the card must be installed. Links to the component & card are below...

https://github.com/nielsfaber/scheduler-component

https://github.com/nielsfaber/scheduler-card

[mjpsr11]

Found it. Now deciding to switch over to HA for scheduling or let the EasyTouch continue it's thing.

Thanks!

[FlaMike]

I am using the Scheduler-component & card along with njcPC & njPC-HA exclusively for my Easy Touch 2 4 control. Have a card in the HA dashboard that indicates the current pool state and allows me to control the pool manually. (Pool lights are on an outdoor lighting card) It's been installed since September or thereabouts and has been very reliable. Super support from the njcPC and njcPC-HA folks, too!

[mjpsr11]

Cool. This is my dashboard so far for my EasyTouch. Will give the schedule a test trial.

[calisro]

Curious. If you walk out to your easy touch control panel, and you turn your pool on or spa or waterfall, or etc, are those correctly reflected in njs-HA? Mine is not.

[FlaMike]

Sweet! I should probably make mine snappier like yours is. Hope it all works out for you!!

[Crewski]

Just FYI, the ability to enable/disable njs-PC schedules have been added to the njsPC-HA integration. You can find them in the appropriate device they are controlling.

[FlaMike]

Thanks for letting us know! I've not away for a bit so I've not yet upgraded to the newest version but will do so soon.

Hope you're able to enjoy your pool at long last!

[Crewski]

Yep, pool has been up and running. I'm having an issue with my temp sensors so need to get that figured out, but I'm limping along!

[FlaMike]

Glad you're up & running (dare I say "In the swim?" Naw!). Hope the temp sensor issue isn't anything significant to get going. I've been swimming since May 1--by decree I turned on the heat & that was that. Needed to heat it again last week--unusual for us so late in the spring. The pool is still "refreshing" when you get in--around 78 degrees, but it's great for lap swimming once you get in a few hundred feet to warm up. I'm sure within a few weeks the pool will be in the upper 80s. That poses a different lap swimming challenge--hot!!!

[rstrouse]

Mine hit 90 last weekend. Back down to 87 now.

[FlaMike]

Toasty! No need to heat the spa if the pool is 90. Nice in the evenings, I'll bet. I can handle doing laps at 87, but 90 gets to be punishing for me.

We've been in the Panhandle for 12+ years & I can't recall a time when the pool was in the 70s in June. I just hope we're not cooler than that in October (without heating the pool, of course). My wife won't even get in the pool if it's not in the mid 80s. She used to swim when it was in the mid 70s, but no more.

[drcooper345]

@Crewski Loving the integration. Feature request here unless it already exists and I just can't find it. I have a IPS flow cell with a built in dry contact switch that is connected through REM. It throws the "No Flow Detected" alarm in dashpanel. I want to use this state to send myself a notification, or perform some other automation functions but I am not sure how to access that sensor in HA.

Any ideas on how to access?

[Crewski]

@drcooper345 I just pushed out v0.4.9 that adds a sensor for flowDetected. It'll be in the chem controller device. Let me know if it works for you.

[drcooper345]

Tested and works. Thank you very much!

[Crewski]

I just pushed out v0.4.11. All incoming messages are now sent to the event bus. You can listen to them on event njspc-ha_event. This way if there is something the integration is missing, you can still get access to the data to roll your own. If it's something you think should be added to the integration just let us know.

[DrJeff]

very nice, thanks!

[calisro]

Hi. This is great. I don't see all messages being sent to the bus though. For example, when I toggle a feature on/off the data is not being picked up on the bus. Really any of the 'features' do not show. When the Circuit itself is toggled, I do see teh event but not through a feature.

I think this is an example of hte messages missed.

[alexdelprete]

@Crewski is your pump connected to the Aquarite through the digital inputs connector or did you connect it through RS485 to njs-PC? Because in the OP I see RPM and Watts and I wondered how you got those, AFAIK the Aquarite have the digital inputs to select the 3 speeds plus the on/off, right?

I am about to install an Aquarite+ and a VS pump that has both digital inputs for the speed selection but it also has A/B connections for RS485, initially I planned to use the digital inputs but knowing RPM and Watts would be very useful, so maybe the RS485 connection (to njs-PC I guess) makes sense.

Thanks for any advice on this...

[Crewski]

My pump was connected to njs-PC via Rs485 initially, which is why I was getting rpm/wattage readings. I’ve since switched to using the relay control of the pump, but that was a personal preference due to some issues I had. My advice would be to hook directly to njs-PC whenever possible. RS485 is definitely where I would start.

…

On Sat, Jul 22, 2023 at 11:23 AM Alessandro Del Prete < ***@***.***> wrote: @Crewski <https://github.com/Crewski> is your pump connected to the Aquarite through the digital inputs connector or did you connect it through RS485 to njs-PC? Because in the OP I see RPM and Watts and I wondered how you got those, AFAIK the Aquarite have the digital inputs to select the 3 speeds plus the on/off, right? I am about to install an Aquarite+ and a VS pump that has both digital inputs for the speed selection but it also has A/B connections for RS485, initially I planned to use the digital inputs but knowing RPM and Watts would be very useful, so maybe the RS485 connection (to njs-PC I guess) makes sense. Thanks for any advice on this... — Reply to this email directly, view it on GitHub <#559 (comment)>, or unsubscribe <https://github.com/notifications/unsubscribe-auth/AB5EC6KZXL3VX2RKUAFBCYLXRPV7FANCNFSM55CMANFQ> . You are receiving this because you were mentioned.Message ID: <tagyoureit/nodejs-poolController/repo-discussions/559/comments/6516922@ github.com>

[tagyoureit]

It's most likely a T9 equivalent. But of course they don't make it easy to compare apples to apples.

[alexdelprete]

The T9 is 20g/h, the RC33 is 33g/h, so it's more like the T15 (30g/h).

I guess it's Sugar Valley introducing new stuff every once in a while.

I found the english info, if needed:

• Model webpage: https://www.hayward-pool.co.uk/catalog/salt-chlorinators/aquarite-sv-salt-chlorinator
• Datasheet: https://www.hayward-pool.co.uk/document/302/technical-data-sheet-aquarite-sv-salt-chlorinator.pdf
• Manual: https://1550743538.rsc.cdn77.org/production/media/4/4/5/9/f06dbc.pdf
• Parts: https://www.hayward-pool.co.uk/document/977/products-parts-aquarite-sv-salt-chlorinator.pdf

[alexdelprete]

@tagyoureit I forgot to link the most important part, the modbus register map for the NeoPool Control System by Sugar Valley, which is basically what the Hayward Aquarite+ is based on (it's the Sugar Valley Hidrolife). Other brands use the same board: Hidrolife, Aquascenic, Oxilife, Bionet, Hidroniser, UVScenic, Station, Brilix, Bayrol, etc.

https://www.welldana.dk/media/wysiwyg/attachments/Manualer/D30-190045_MODBUS%20REGISTER%20DESCRIPTION_MANU_EN.pdf

Would be great if njs-PC could support the NeoPool. Right now I had to revert to Tasmota's NeoPool implementation, and it works fine:

I'm using M5Stack Atom Lite connected to its Tail485 addon (on the bottom). I chose this because the Atom Lite is a very good ESP32 device, I use it for other projects too, and in this case the real benefit is the Tail485 addon that integrates a 9-24V DC/DC voltage regulator, that outputs the 5V needed to power the Atom Lite. This means that no external power supply is needed when connected to an RS485 interface that also offers a power pin, like the Aquarite+ with its 12v pin. So basically you have a very small device (it's like two coins), that you can connect and power inside the Aquarite+ directly.

The cost is $15 total: https://shop.m5stack.com/pages/search-results-page?q=m5%20atom

[tagyoureit]

I added this to the wishlist (project and discussion thread). It might be quite a while before this gets added because it would be supporting a whole new protocol, but we will track it.

[alexdelprete]

Thanks a lot. I assume that "quite a lot" could also mean more than a year right? If that's the case, while waiting, I'll have to dig deep into Tasmota's implementation.

Is there any way to be notified of progresses of a specific "wish"? Otherwise I'll have to poll too much. :)

[FlaMike]

I just switched from njs-PC & dashPanel in a docker container to a "real" Nixie & REM CHEM setup. Really loving your integration even more than before--amazing amount of information available to HA.

Are alarm conditions from Nixie/REM CHEM available to HA with your integration? I am wondering if things like low acid tank level, pH or ORP out of range, etc. can be seen from HA.

Thanks!

[Crewski]

Honestly it's been a while since I've looked at the code. Let me look into it and get back to you. Gotta get back in the swing of things since I'll be opening the pool next month.

[FlaMike]

Thank you in advance for checking on its feasibility! I truly appreciate your efforts & the integration. If you need a beta tester or if I may be of any other assistance, please let me know.

Still a little to chilly in north Florida as well, but really looking forward to getting back in the swim soon! I think you've had a couple of cold waves in the past few weeks. At least spring is finally here--officially speaking :-)

[raidflex]

How do you add pump speed control in HA when using RS-485 for the pump? I have a SuperFlo VS setup through RS-485 and can control the speed through the nodejs-poolcontroller. But there seems to be no way to control it through HA. I tried creating a pump circuit in the nodejspool-controller dashPanel, but there is no entity created for this in HA.

I do get all the states, like RPM, Watts, etc, just no way to control RPM.

[lockeandev]

I've been using this integration for over a year, but when to get my pool started for the season again and not the integration is broken/won't start up.

This is the output of the logs for the integration when trying to reload it. Any idea on why it will not start?

Logger: homeassistant.config_entries
Source: config_entries.py:753
First occurred: 8:06:54 AM (3 occurrences)
Last logged: 12:07:00 PM

Error setting up entry njsPC-HA for njspc_ha
Traceback (most recent call last):
File "/usr/local/lib/python3.13/site-packages/aiohttp/connector.py", line 1116, in _wrap_create_connection
sock = await aiohappyeyeballs.start_connection(
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
...<5 lines>...
)
^
File "/usr/local/lib/python3.13/site-packages/aiohappyeyeballs/impl.py", line 122, in start_connection
raise first_exception
File "/usr/local/lib/python3.13/site-packages/aiohappyeyeballs/impl.py", line 73, in start_connection
sock = await _connect_sock(
^^^^^^^^^^^^^^^^^^^^
...<6 lines>...
)
^
File "/usr/local/lib/python3.13/site-packages/aiohappyeyeballs/impl.py", line 208, in _connect_sock
await loop.sock_connect(sock, address)
File "/usr/local/lib/python3.13/asyncio/selector_events.py", line 641, in sock_connect
return await fut
^^^^^^^^^
File "/usr/local/lib/python3.13/asyncio/selector_events.py", line 681, in _sock_connect_cb
raise OSError(err, f'Connect call failed {address}')
ConnectionRefusedError: [Errno 111] Connect call failed ('192.168.0.82', 4200)

The above exception was the direct cause of the following exception:

Traceback (most recent call last):
File "/usr/src/homeassistant/homeassistant/config_entries.py", line 753, in __async_setup_with_context
result = await component.async_setup_entry(hass, self)
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
File "/config/custom_components/njspc_ha/init.py", line 59, in async_setup_entry
await api.get_initial()
File "/config/custom_components/njspc_ha/init.py", line 273, in get_initial
async with self._session.get(f"{self._base_url}/{API_STATE_ALL}") as resp:
~~~~~~~~~~~~~~~~~^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
File "/usr/local/lib/python3.13/site-packages/aiohttp/client.py", line 1425, in aenter
self._resp: _RetType = await self._coro
^^^^^^^^^^^^^^^^
File "/usr/local/lib/python3.13/site-packages/aiohttp/client.py", line 703, in _request
conn = await self._connector.connect(
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
req, traces=traces, timeout=real_timeout
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
)
^
File "/usr/local/lib/python3.13/site-packages/aiohttp/connector.py", line 548, in connect
proto = await self._create_connection(req, traces, timeout)
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
File "/usr/local/lib/python3.13/site-packages/aiohttp/connector.py", line 1056, in _create_connection
_, proto = await self._create_direct_connection(req, traces, timeout)
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
File "/usr/local/lib/python3.13/site-packages/aiohttp/connector.py", line 1411, in _create_direct_connection
raise last_exc
File "/usr/local/lib/python3.13/site-packages/aiohttp/connector.py", line 1380, in _create_direct_connection
transp, proto = await self._wrap_create_connection(
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
...<7 lines>...
)
^
File "/usr/local/lib/python3.13/site-packages/aiohttp/connector.py", line 1135, in _wrap_create_connection
raise client_error(req.connection_key, exc) from exc
aiohttp.client_exceptions.ClientConnectorError: Cannot connect to host 192.168.0.82:4200 ssl:default [Connect call failed ('192.168.0.82', 4200)]

[tagyoureit]

Cannot connect to host 192.168.0.82:4200

Look into the ip address or connection parameters.

[lockeandev]

Well, that was easy. I should have seen that. For some reason when I power cycled the pool control panel, the rasp pi running njsPC switched to wifi instead of Ethernet and got a different IP than the integration was looking for...

Thanks!

[TheBobC]

Hello. I am hoping someone can comment on what I am trying to make happen. For history, I have a Hayward Aqua Pro controller with the T15 SWG and an Ecostar VSP pump. Some time ago, something bad happened to my Aqua Pro and it fell prey to the COMM ERROR. As I did not want to spend $$$$ on a new board, and I have some experience in the RPI world, I came across njsPC. I was able to set it up so a PI4 board ran njsPC and controlled my Ecostar, and the Aqua Pro continued to run my SWG. I loved the idea of monitoring my system via my HA setup, so I got the integration off of HACS and had the communication there. But the SWG info was not, as there was no communication to the Aqua Pro. I ran across a guy that did board exchanges for the Pro for a reasonable amount, and got a reconditioned board. Now, I would like to set up the system as Hayward designed, Aqua Pro controlling the pump (via data, not relay as directed by Hayward), the SWG and my pool light. But I would also like to keep my PI4 and njsPC involved and controlling those devices through the Aqua Pro. Is this possible, and if so, where to I connect the RS 485 to the Aqua Pro? The pump utilizes the upper left connection. There are two comm ports in that upper left area under the antenna plug, but I do not know the pinout for them. Is what I want to do possible? What connections?

[tagyoureit]

You can piggyback rs485 connections. They don't need their own port. But the Aqua Pro is just a salt chlorine controller so I'm not sure about what will be controlling your pump. Can you explain?

[TheBobC]

Ah, I did not know that about rs485. Thank you. And apologies, too many Aqua's floating in my head from so much reading. I have the Aqua Plus, designed to control pump, valves, lights, SWG, etc. Will that allow me to control from HA via njsPC?

[TheBobC]

Not sure what I missed. The only information that shows up on njsPC is the pump speed and power. No pool temp, no salt level, etc. When i was controlling the pump directly, I understood I needed to set up circuits, schedules, etc. What do i need to set up if I simply (for starts anyway) want to be able to see things on HA?